Top 8 Best 4 Way Clamps For Woodworking

Clamping panels can certainly be a challenge. Especially when we try to use everyday pipe clamps or bar clamps. While these types of clamps work fairly well on certain glue up projects, the one thing they dont do at all is apply pressure from the top and bottom of the panels during glue up. In fact, with all the pressure being applied on both sides, bar and pipe clamps will almost certainly bow, buckle or rack your panel glue up project.. Lets make racked panel glue ups a thing of the past The uniquely designed 4 way pressure solves this age old issue by applying pressure to all four sides of your panel glue up. With a simple turn of the rotating clamp handle, all four sides of the clamp will draw inward at the same time. This provides equal pressure on to your panel and prevents bowing, buckling, or racked panels.. Build any length clamp with the durable plastic bars with 4 notches for maximum adjustability to handle a variety of stock widths. Clamp can be used for boards up to 6 inches in thickness by simply adjusting the clamp width capacity with the appropriate number of notches. Turn the handle clockwise to tighten the clamp and turn the handle counter clockwise to release pressure. The 4 way pressure clamp is equipped with side pressure pads to prevent damaging your stock.. Now you can confidently glue up wide boards, shelving, table tops, and more up to 6 thick. To setup the clamps simply attach the clamp to any length 2 x 2s 2 x 4 ripped in half with the the wood screws that are provided, apply wood glue to your project, set the clamps on to your panel boards and turn handle to tighten the clamp on all four sides. We recommend that you place a 4 way pressure clamp every 12 to 18 for best results.. This clamp package comes with two full 4 way pressure clamp assemblies. Includes 2 each rotating handle assemblies, 2 each tailstock assemblies, 4 each side pressure pads and 12 each 4 notch bars. Together, this setup will allow you to create two 4 way pressure clamps. More than one clamp is generally recommended for any project over 12 in length. Wood is required for setting up the clamp. Wood is NOT included..

LARGE PANEL GLUE-UPS The DCT 4-Way Pressure Release Clamp Wood Panel Corner Clamping System Woodworking Bracket Set handles stock up to 6 inches 15.2cm thick for simplifying the process of gluing table tops, countertops, furniture panels, cabinet doors, and more and saves you from using additional clamps to keep the glue-ups straight. 4-WAY Stock stays flat and prevents buckling of boards during glue-up because of the equally applied pressure from all four directions top, bottom, and both sides Ideal for gluing table tops, shelving, veneer, laminates Durable clamp only limited by the quality of prep and glue used. EASY TO USE Assembly instructions included More convenient than lining up standard clamps and cauls Attach notched bars to any length 1.5-inch x 1.75-inch 3.2cm x 4.4cm board equivalent to a 2x4 ripped in half with provided screws, set clamp and turn handle to tighten on large pieces, we recommend one clamp every 18 inches45.7cm for maximum clamping efficiency Make sure the 2x4s you use are not twisted Drill pilot holes for the outer-most screws when attaching the pressure pads. ADJUSTS TO YOUR PROJECT Build any length clamp with the durable plastic bars with 12 notches for maximum adjustability to handle a variety of stock widths Clamp can be used for boards up to 6 inches in thickness by simply adjusting the clamp width capacity with the appropriate number of notches Turn the handle to tighten the clamp and unwind the turn handle to release pressure Clamp has pressure pads to prevent damage to the edge of your stock. CONTENTS Package includes 2 12.75-inch long notch bars, 2 6.9-inch long notch bars, 1 clamp assembly head, 1 clamp assembly tail, 16 assembly screws 4x 38-inch, 12x 1-14-inch L, and assembly instructions 1 set with 1 clamp multiples needed for projects over approximately 2 feet61cm Wood required, not included.

Clamping panels can certainly be a challenge. Especially when we try to use everyday pipe clamps or bar clamps. While these types of clamps work fairly well on certain glue up projects, the one thing they dont do at all is apply pressure from the top and bottom of the panels during glue up. In fact, with all the pressure being applied on both sides, bar and pipe clamps will almost certainly bow, buckle or rack your panel glue up project.. Lets make racked panel glue ups a thing of the past The uniquely designed 4 way pressure solves this age old issue by applying pressure to all four sides of your panel glue up. With a simple turn of the rotating clamp handle, all four sides of the clamp will draw inward at the same time. This provides equal pressure on to your panel and prevents bowing, buckling, or racked panels.. Build any length clamp with the durable plastic bars with 4 notches for maximum adjustability to handle a variety of stock widths. Clamp can be used for boards up to 6 inches in thickness by simply adjusting the clamp width capacity with the appropriate number of notches. Turn the handle clockwise to tighten the clamp and turn the handle counter clockwise to release pressure. The 4 way pressure clamp is equipped with side pressure pads to prevent damaging your stock.. Now you can confidently glue up wide boards, shelving, table tops, and more up to 6 thick. To setup the clamps simply attach the clamp to any length 2 x 2s 2 x 4 ripped in half with the the wood screws that are provided, apply wood glue to your project, set the clamps on to your panel boards and turn handle to tighten the clamp on all four sides. We recommend that you place a 4 way pressure clamp every 12 to 18 for best results.. This clamp package comes with two full 4 way pressure clamp assemblies. Includes 2 each rotating handle assemblies, 2 each tailstock assemblies, 4 each side pressure pads and 12 each 4 notch bars. Together, this setup will allow you to create two 4 way pressure clamps. More than one clamp is generally recommended for any project over 12 in length. Wood is required for setting up the clamp. Wood is NOT included..

4-way action of panel clamp applies even pressure to glue joints. Will accept material from 12-inch to 3-12-inches thick of unlimited length. Use while gluing table tops, furniture panels and doors. Package Weight 4.0 pounds.

WELL CONSTRUCTED - Our corner clamps are made of high-quality material, it is light and durable.The Compact, Strong, Heavy duty spring is made of stainless steel, smooth and durable. Protective rubber keeps from scratching your frame.It could hold the block tightly, but not too tight.Clamping force is about 10 lbs.. ADJUSTABLE EASY TO USE - These corner clamps are adjustable, can fit 0.32 - 1.06 thick board and work for 90 degree corner, T-joints,L-joints and F-joints. Fit 0.24 - 0.75 thick board for 60 degree and 0.4 - 1.26 thick board for 120 degree. Also allows you to working with two different thickness board. Its compact and well-sized design fits naturally in your hand for comfortable control so that you can operate the spring clamp only by one hand.. MULTIFUNCTIONAL WIDELY USED - These Corner Clamps are very suitable for welding, drilling, making cabinets, photo framing,woodworking, cabinet and furniture repair connection,wooden DIY, etc.It is extremely good for very small wood projects like photo frames, you can build bee boxes, cabinets and alot of drawers.. PACKAGE INCLUDED - Set of 4 Right angle clamps.They are completely multifunctional great for screwing or glueing boards or for small projects just to give you some hold. Help you save labor time, reduce the workload.. BUY WITH CONFIDENCE - We are committed to 100 customer satisfied serve. If you have any question with the item , please contact us , well reply and solve your problem within 24 hours. Thanks for your choice.

Trustworthy QualityWETOLS 90 right angle clamp is uniquely prepared with the aluminum alloy die-casting based construction, where high durability and well-built design are conveyed to ensure long-lasting use.. Clamping Range Maximum clamping range is approx. 2.75in70mm jaw width 3.74in95mm jaw depth 1.4in35mm, allowing two different thicknesses wood block to be connected at right angle. It can accommodate most large things including metal tube, steel rod, wood, thick glass, and more.. Swing Jaw Design Wood Clamp's single-handle jaw can be rotated in two-way, making clamping more convenient and holding work pieces precisely.. Ergonomic DesignAnti-skid handle is nicely covered with rubber to ensure users comfort for hands. Whether for professional use or DIY use, WETOLS 90-degree corner clamps are absolutely useful tools to choose.. Versatile Use WETOLS Wood Clamp is perfect for welding, framing, drilling, doweling, woodworking, making cabinet, installing furniture, box and picture frames, etc..

Adjustable angle It is helpful for woodworkers and carpenters to fix two boards or glass between 60 degrees, 90 degrees, and 120 degrees.. Easy to use Easy to operate, save labor time and reduce workload. Solid and anti-skid, helps to set up instantly and secure quickly.. Scope of application Ideal for use in welding, framing, drilling, doweling, woodworking, making cabinet, installing furniture, box and picture frames, etc.. Product combination A set of 4 angle clamps can ensure the fixed square, triangle, T shape and other desired shapes.. Complete set of accessories Package accessories include 4 sets of 6090120 degree angles..

NO MORE TOOLS Set your tools aside when installing your ductwork or hose with these handy, easy to tighten hoseduct clamps. Place the clamp where its needed then simply turn the key to loosen or tighten them.. LARGE EASY TO TURN KEY - The easy to turn and easy to see blue key is made from a strong and durable polymer. The key is designed to make the securing and un-securing of hose much easier on the knuckles. No more knuckle busting flat head screw drivers or tiny socket wrenches. Simply to turn the key clockwise to tighten, counter clockwise to loosen.. OFTEN USED IN THESE APPLICATIONS These unique clamps are typically used in securing duct work, dryer vents, dust collection hoses, piping, large cable, pvc tubing and more. Ideal for use in automotive, industrial, mechanical, agriculture, boatmarine, shield, recreational vehicles, household and more. Works for both indoor or outdoor use.. 304 STAINLESS STEEL HOSE CLAMP- The 4 diameter large hose duct clamp including the housing, the band and the internal screw are made from premium 304 stainless steel. This makes the clamp strong, durable and rust resistant which makes it ideal for many applications in the shop or around the home.. FLEXIBLE ADJUSTABLE SIZE RANGE- 4 inch hose clamps are flexible and workable with a rather wide adjustable size range from appx. 4-716 4.440 or 112.77mm in full diameter down to appx. 3-716 3.440 or 87.32mm at its most compact diameter..

RUBBER PADS TO PROTECT WOOD PIECES Each angle clamp includes 2 rubber pads to protect your wood pieces from any damage.The pads can be removed for bigger wood pieces to fit.. QUALITY FRAMING CLAMPS Not only for the 90-degree angle, T-joints, but also for the 45-degree saw. The 4 set clamps for woodworking are made of durable ABS plastic and strong tension spring for firm clamping.. ONE-HAND OPERATION The woodworking clamps are easy to use. You can open this clamp with one hand, and the other hand is free for the workpiece, convenient and simple. The clamp will be a best gift for woodworkers, handymen and DIY.. ACCURATELY SET FOR EVERY RIGHT ANGLE These compact clamps with its versatility allows to use it for framing, doweling, drilling, preparing cabinet, furniture installation, etc. In addition to that, right angle clip can also be used to make miter joints as well. HIGH PRACTICALITY Perfect for small wood working project, to build wooden boxes, picture frames, birdhouse,mailbox, dresser drawers assembly. WORK EFFICIENTLY The advantage of having 4 pack angle clips is that you can square and set entire side of wood box in one. STRONG AND STABLE High spring tension to keep boards in place when screwing or gluing them together.

Maximum Opening Capacity 4 inches. Throat depth is 3 inches.. Maximum Load Limit 600 pounds.. Rapid Action The handy quick release button releases the clamp instantly. With a quick push on the power bar the gear clamp is easy to adjust and release.. Minimal Movement During Tightening Holds very well and doesn't cause shifting or twisting while tightening. . Note Open the handle to the maximum then slide to clamp whatever your clamping then pull the lever towards the black bar..