Top 8 Best Arduino Motor Driver

L298N as main driver chip makes strong driving abilitysmall heatingstrong anti-interferencelow calorific value. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. Dual-channel H-bridge driver working mode creates higher working efficiency. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage. Large capacity filter capacitance, afterflow protection diode, more stable and reliable.

Package 2 pcs.

Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability,low calorific value and strong anti-interference ability.. This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage of the voltage stabilizing chip,please use an external 5V logic supply when using more than 12V driving voltage.. Using large capacity filter capacitor,this module can follow current to protect diodes,and improve the reliability.. Dual-channel H-bridge driver working mode creates higher working efficiency. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.

This is a commonly used DC motor drive module, using a small current 293 chip DC motor driver chip.. Using this chip you can use DC motors and power supplies of up to 10 Volts, that some pretty big motors and the chip can supply a maximum current of 600mA per channel.. Tested compatible for Arduino Mega, Diecimila Duemilanove.. 2 interface for 5V Servo connected to the Arduino's high-resolution dedicated timer - no jitter.. Multi-function, easy to operate, a strong driver library support and feature updates..

This is a good parts kit for RC car project. It not only comes with 4pcs wheels and motors, but also 2pcs motor drive modules and 60pcs jumper wires, which are very useful accessories for your project.. Motor Drive Controller L298N used as the main driver chip. It has the strong driving ability, low calorific value and strong anti-interference ability.. TT Motor The motor is a two-axis motor with a reduction ratio of 148, which has strong anti-interference ability.. Smart Car Wheels The wheels are made of high-strength plastic and the tires are made of durable black rubber.. To avoid damage the voltage stabilizing chip of Motor Drive Module, please use an external 5V logic supply when using more than 12V driving voltage..

5V isolate with MCU, and effectively protect MCU 5V power indicator on board.. Voltage indication of motor driver output end can solder heat sink.. Just need four lines from MCU to driver module GND. 5V. PWM1. PWM2 isolation chip 5 V power supply can share with MCU 5 V.. Able to reverse the motor forward, two PWM input frequency up to 25kHZ two heat flow passing through an error signal output.. Isolated chip 5V power supply can be shared with the MCU 5V, can also use the on-board 5V supply the supply voltage 5.5V to 27V..

Simple step and direction control interface,Take anti-static measures before you use the A4988 modules in case of short-circuit. Five different step resolutions full-step, half-step, quarter-step, eighth-step, and sixteenth-step. Output drive capacity of up to 35 V and 1.2 A. Adjustable current control lets you set the maximum current output with a potentiometer. Intelligent chopping control that automatically selects the correct current decay mode fast decay or slow decay. Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection.

Communication Interface IIC. 16-way steering gear control. Voltage DC5-10V power supply. The PCA9685 chip is wrapped in the center of the board. All PWM output lines have a 220 ohm series resistor protection and can easily drive LED..

The Motor Shield is based on the L298 , which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors.. It lets you drive two DC motors with your board, controlling the speed and direction of each one independently.. You can also measure the motor current absorption of each motor, among other features.. Motor drive voltage external input 3-35V, internal input 6-12V. Max current 2A per channel or 4A max with external power supply.

Stepper motor with a standard interface, when used directly pluggable.. A, B, C, D four-phase LED indicates the status of the stepper motor work.. 5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development boardWith convenient use, direct docking. Drive Module Board Sizein 1.371.180.6 Stepper Motor diameter 1.06in Stepper Motor lines 9.45in. Great packing in a box 5 set Uln2003 Stepper Motor Driver Board with a little gift.