Top 8 Best Arduino Motor Shield

Control speed and direction for two DC motors, or just speed with four DC motors drive a large stepper motor up to NEMA 17.. Connect other sensors and actuators through the shields Molex connectors.. Connect more to your board It works also for up to four external relays or solenoids.. Works with your Arduino Uno, Uno SMD, Mega, and Leonardo.. External power input to separate the motor power from the microcontroller one..

The Motor Shield is based on the L298 , which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors.. It lets you drive two DC motors with your board, controlling the speed and direction of each one independently.. You can also measure the motor current absorption of each motor, among other features.. Motor drive voltage external input 3-35V, internal input 6-12V. Max current 2A per channel or 4A max with external power supply.

This is a commonly used DC motor drive module, using a small current 293 chip DC motor driver chip.. Using this chip you can use DC motors and power supplies of up to 10 Volts, that some pretty big motors and the chip can supply a maximum current of 600mA per channel.. Tested compatible for Arduino Mega, Diecimila Duemilanove.. 2 interface for 5V Servo connected to the Arduino's high-resolution dedicated timer - no jitter.. Multi-function, easy to operate, a strong driver library support and feature updates..

Ship From Balance world. Operating Voltage 5V to 12V. Motor controller L298P, Drives 2 DC motors or 1 stepper motor. Max current 2A per channel or 4A max with external power supply. More detail see description.

New version 2.3. Completely stackable design 5 address-select pins means up to 32 stackable shields that's 64 steppers or 128 DC motors What on earth could you do with that many steppers I have no idea but if you come up with something send us a photo because that would be a pretty glorious project.. Instead of a L293D darlington driver, we now have the TB6612 MOSFET driver with 1.2A per channel and 3A peak current capability. It also has much lower voltage drops across the motor so you get more torque out of your batteries, and there are built-in flyback diodes as well.. Instead of using a latch and the Arduino's PWM pins, we have a fully-dedicated PWM driver chip onboard. This chip handles all the motor and speed controls over I2C. Only two pins SDA SCL are required to drive the multiple motors, and since it's I2C you can also connect any other I2C devices or shields to the same pins. This also makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3.. As of 3212014 we are shipping motor shields with the terminal blocks, and power jumper pre-soldered on. You'll still need to do a little soldering to put on the shield-headers or stacking headers but it should be even easier and faster to get started.

H-Bridges TB6612 chipset provides 1.2A per bridge 3A peak. Chip TB6612FNG motor driver chip. Completely stackable design 5 address-select pins means up to 32 stackable shields. Characteristic Arduino interface is fully compatible expansion. Feature Motors automatically disabled on power-up.

Motor Shield for Arduino Uno, Uno SMD, Mega and Leonardo. L298P Motor Driver Shield.

L293D motor drive shield expansion board is a commonly used DC motor drive module, using 293D chip small current DC motor driver chip. The pins are made Arduin compatible, which also facilitates the quick Arduin-based development for enthusiasts.. Up to 4 bi-directional DC motors with individual 8-bit speed selection so, about 0.5 resolution. Up to 2 stepper motors unipolar or bipolar with single coil, double coil, interleaved or micro-stepping.. 4-Channel H-bridge L293D chipset provides 0.6A per bridge 1.2A peak with thermal shutdown protection, can run motors on 4.5V to12V.. 2 connections for 5V hobby servos connected to the Arduino's high-resolution dedicated timer - no jitter Tested compatible with Mega, Diecimila and Duemilanove. Arduino is a great starting point for electronics, and with a motor shield it can also be a nice tidy platform for robotics and mechatronics. L293D motor drive module is a design for a full-featured motor shield that will be able to power many simple to medium-complexity projects..

Connect an MKR board to a Controller Area Network CAN Bus and readwrite tofrom other devices in the network.. Program your Arduino MKR boards to become CAN peripherals and controllers.. Possible applications Smart dashboards to existing vehicles, autonomous cars, drones, and industrial machinery.. Use the MKR CAN shield to connect to several types of industrial grade sensors, motors and displays.. Works for any of the Arduino MKR boards, and can be stacked on top of other MKR Shields.

Driven part of the input voltage VS VIN Input 6.5 12V, PWRIN 4.8 35V input.. The L298P shield DC motor driver has PWM speed control mode dual high-power H-bridge driver.. Adopt dedicated high-power motor driver chip L298P which can directly drive two DC motors with drive current up to 2A.. Stack design can be directly plugged into the Arduino, easier to use.. Adopt dedicated high-power motor driver chip L298P which can directly drive two DC motors with drive current up to 2A..