Top 8 Best H Bridge Motor Driver

L298N as main driver chip makes strong driving abilitysmall heatingstrong anti-interferencelow calorific value. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. Dual-channel H-bridge driver working mode creates higher working efficiency. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage. Large capacity filter capacitance, afterflow protection diode, more stable and reliable.

Size 18.516mm. Input voltage 3-10V. Single H bridge output current 1.5A, can drive 2 DC geared motors.. Built-in overcurrent protection, short circuit protection, undervoltage lockout and overtemperature protection. With low power sleep mode.. For DIY smart car robot, it can drive DC motors up to 1.5A and 4-wire stepper motors..

NOYITO 170W High-power H-bridge Motor Drive Module is composed of H-bridge driver IC and 4 low-pass internal resistance 55V 110A NMOS tubes. It has the characteristics of small heat generation and good motor braking effect.. 2-Channel PWM inputs, the duty cycle can be adjusted between 0-100, with instantaneous braking capability.. Supports 3.3V and 5V logic inputs. It is suitable for MCU IO ports to directly control the motor, and it can also control the motor's forward and reverse rotation through analog input.. Module working voltage 10V-30V. Power 170W max.. Suitable for 5-40V motor.The second picture on the left is the wiring diagram. NOYITO 170W High-power H-bridge Motor Drive Module User Manual Schematics Wiring Diagram. https1drv.msusAlzQUCOyZQhKggdGTmoExd0-JMLBe2rVeoZ.

Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability,low calorific value and strong anti-interference ability.. This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage of the voltage stabilizing chip,please use an external 5V logic supply when using more than 12V driving voltage.. Using large capacity filter capacitor,this module can follow current to protect diodes,and improve the reliability.. Dual-channel H-bridge driver working mode creates higher working efficiency. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.

Dual H-bridge, capable of driving two DC motors instantly, single circuit 7A current, high power. Logic voltage 5V. Signal optocoupler isolation input, can be directly controlled by 10 ports without interference. Undervoltage protection to prohibit instantaneous high current from burning out the module. High power TVS and electrostatic discharge circuit, suppressing transient interference pulses and static electricity,improving EMC performance, stable and reliable product, industrial grade design..

9.3mm x 6.4mm x 3.2mm. Height with pins 7mm.

Dual bts7960 high current 43A H-bridge drive The power supply voltage is 5.5 to 27V Isolation chip 5V power supply can share 5V with MCU.. It is isolated from the single-chip microcomputer 5V to effectively protect the single-chip microcomputer.. It can realize the forward and reverse rotation of the motor, and the maximum frequency of two PM inputs is 25kHz Two over-current thermal error signal outputs.. Just need four lines from MCU to driver module GND. 5V. PWM1. PWM2.. Package included3pcs BTS7960 43A High Power Motor Driver Module Smart Car Driver Module..

DROK DC motor driver input voltage range is DC 6.5V-27V, can be input DC 12V or 24V, rated output current of each port is 7A, total output power is 160W.. STRONG DRIVE the motor controller board adopts dual H bridge, can drive two DC motors at the same time.. FORWARD and REVSERSELY ROTATE the IN1, IN2IN3, IN4 port can control forward or reverse motor rotation.. PWM SPEED CONTROL enable signal terminal ENA input PWM can regulate speed, PWM frequency range 0-10KHZ.. UNDER VOLTAGE PROTECTION the motor driver module is with under voltage protection to prevent instantaneous large current from damaging the module..

HiLetgo L9110S H-bridge DC Stepper Motor Driver Controller Board. Dual motor driver chip L9110S. Module supply voltage 2.5-12V.