Top 8 Best Heat Strips For Pipes

24Ft x 120V x 7Wft.. Keeps water flowing down to -40 degrees F. For metal and plastic water pipes. Easy to install.

BUILT-IN THERMOSTAT - Turns the cable on at 38 degrees F and prevents frozen pipes to -50 degrees F - Simply wrap on, insulate and plug in. Insulation sold separately.. PRESS-TO-TEST BUTTON - Exclusive feature to test cable before or after installation.. ENERGY EFFICIENT - Uses up to 65 less energy at 2 watts per foot vs other cables at 7 watts per foot.. USE ON ALL RIGID PIPES - PVC, CPVC, copper and metal pipes.. MADE IN THE USA.

6Ft x 120V x 7Wft.. Keeps water flowing down to -40 degrees F. For metal and plastic water pipes. Easy to install.

Prevents Frozen Water Pipes To -50F. Easy To Install Just Wrap Around Application. Sensor Light Shows Thermostat Is Working. Brand Name M-D Building Products.

Use for water filled plastic including PEX or metal pipes. Not use for anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines and so on. Two year limited quality . If you are not completely satisfied with HEATIT heating cable, please don't hesitate to contact our customer service in any time, we'll try our best to solve your issues.. Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 wattsft. Built in thermostat to turn the cable 68F on39F off. Only use 5 amps or less of electricity. Energy saving. 100 screen rate with the Aluminum foil and tinned copper braid.. Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC high-low temperature as out jacket.. Maximum 12 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 38'' and less than 1 12'' in. diameter. No crossing. No spiral. No overlap itself. Only straight.. Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don't plug in the cable for a long time for testing. When you feel the slight warm, please turn it off.. Copper.

3Ft x 120V x 7Wft. Keeps water flowing down to -40 degrees F. For metal and plastic water pipes. Easy to install.

18 ft. Length.. 120V, 7 watts per ft.. Keeps water flowing down to -40 degrees F.. For metal and plastic pipes.

SWISS Manufactured Commercial Grade with 100 Quality Control ETL certified. 30 YEARS of successful experience in electric heating cables. REDUCE ENERGY COSTS Cables automatically adjust heat output to ambient temperature Operates in temperatures down to negative 40 degrees Save energy no thermostat needed. PROTECT YOUR HOME Our product will give you peace of mind knowing that you and your home are PROTECTED from any potential damage caused by burst pipes or the inconvenience of no running water. HOW TO USE Use for heating FRESHWATER supply pipes, SEWER pipes, DRAINAGE pipes, TANKS or SOIL heating Can be used on all METAL AND NON-METAL pipes, including copper, galvanized steel, polyethylene, polypropylene, PVC, etc The cable can be installed INSIDE the pipe if the water is not intended for consumption and is not under pressure Can be overlapped during installation and operationCABLE WONT OVERHEAT. 3-foot cold lead on cable..

This item is a M-D Building Products 4325 6-Foot Pipe Heating Cable with Thermostat. Purpose of use for Rough Plumbing, pipe-heat-cables. This product is manufactured in China. Prevents frozen water pipes to -50 Degree Fahrenheit. Easy to install just wrap around application. Sensor light shows thermostat is working. Available in 6 different lengths. Built in thermostat.

JHSF doesn't work unless the ambient temperature is below 37F3 degree C. Please test the cable in a cold environment.. Suitable for use on plastic and metal water pipes. including inlet pipe,drain pipe, sewer , palm tree frost protection etc. Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable.. Pre-assembled, easy to install. Including grounded plug with light, built in thermostatturn the cable 37F on 50F off and instructions. 120 volt, 3 wattsft at 50 degrees F. Protect pipes up to 2 in diameter. Can be used by straight, spiral and overlap.. ETL approved. 2 ft 183 cold lead with plug. The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE high-low temperature as out jacket. Ingress Protection 65.. Testing the cable before the installation. Uncoil the cable, plug in the heating cable. Normally you can feel the slight warm on the heating cable in few minutes..