Top 8 Best I2c Oled

0.96 inch,Resolution 128 x 64, View angle 160, Support voltage 3.3V-5V DC, Power consumption 0.04W during normal operation, full screen lit 0.08W. Embedded Driver IC SSD1306. Communication I2CIIC Interface, only need two I O ports. It compatibles with R3 board and Mega, Raspberry pi, 51 MCU, STIM 32, etc.. No backlight is required, and the display unit can be self-luminous. It has ultra-high contrast, bright and clear dots, and it is easy to read even small fonts. There are no fonts embedded in the OLED controller, users can create fonts through font generation software..

Application These serial modules can be used for raspberry Pi 4B3B3B2BZero, Beagle Bone Black,Ar duino UNO and Mega, 51 MCU, STIM 32 and so on. Showing graphical textual information directly on your micro-controller projects. 128 X 64 Pixel Needn't backlight, the display unit can self-luminous. It has Super High Contrast, bright and crisp dots, even tiny fonts quite readable.No embedded fonts inside the OLED controller, user can create the fonts through the font generation software. Four square holes are easy to install. Support I2c communication Protocol. Super Low Power Consumption.

Resolution 128 x 32 0.91 Inch OLED display, no need backlight, self-illumination, Display Color White.. Low power consumptio SSD 1306 oled display I2C oled display, IIC I2C communications simplifies connection.. Compatible with Arduino nano, R3 board, Raspberry Pi 4B3B3B2BZero,ESP8266, ESP32, STM32, etc.. Working power3.3-5v, Operating temperature -40 - 85 .. What will you get there are 5 pieces OLED display module OLED display module for you..

Interface Selection to choose SPI or IIC interface through R3, R4, R5. For IIC communication, it is necessary to move the resistor on R4 to R3, and R5 is soldered with 0 ohm resistor.. SPI communication or I2C communication can be switched by configuring three resistors R3 R4 R5.

Interface Selection to choose SPI or IIC interface through R3, R4, R5. SPI communication or I2C communication can be switched by configuring three resistors R3 R4 R5. This is a 2.42 inch OLED display module of 128x64 resolution in which the emissive electroluminescent layer is a film of organic compound that emits light in response to an electric current. Diagonal Screen Size 2.42 inch. Driver IC SSD1309.

Information 128 x 64 View angle more than 160 degree Support voltage 3.3V-5V DC Power consumption 0.04W during normal operation, full screen lit 0.08W. Functional usages 0.96 inch OLED module for showing graphical and textual information directly on your micro-controller projects It supports many chips compatible with Arduino Mega, Raspberry pi, 51 MCU, STIM 32, etc. Embedded driver IC Communication I2CIIC Interface, only need 2 IO ports Compatible with MMDVM, Pi-Star, and it is compatible with Raspberry pi. Self-luminous design needn't backlight, the display can self-luminous It has high contrast, bright and crisp dots, even tiny fonts quite readable. About fonts no embedded fonts inside the OLED controller, user can create the fonts through the font generation software.

Fully compatible with Raspberry Pi, Arduino, 51 series, MSP430 Series, STM322, CSR IC, etc.. High resoluton 12864 pixelsapprox. Support I2c IIC communication Protocol,the IIC address can be changed,it is convenient to use with different machines .. Pin Definitions GND, VCC, SCL, SDAPins 4 pins. Package includes2 x 0.96 inch OLED Display kits Yellow Blue Two-Color, 8x Male to Femal Dupont Wire, 8x Female to Female Dupont Wire.

Resolution 128 64. Driver IC SSD1309. Diagonal Screen Size 2.42 inch. Interface Selection SPIFactory Setting or IICYou need to move the resistor R4 to R3, and solder R5 with 0 ohm resistor.. The driver chip for this screen is SSD1309, which supports 4-wire SPI, I2C and 8-bit interfaces. It does not support 3-wire SPI..

Compatibility blue and yellow, 0.96 inch OLED module is designed to display graphic information and text information directly on your microcontroller project Compatible with Mega, Raspberry pi, 51 MCU, STIM 32, etc.. Product information resolution is 128 x 64 View angle is more than 160 degrees Supporting voltage is from 3.3V to 5V DC Power consumption during normal operation is 0.04W, full screen lit is 0.08W. Driver and communication embedded driver IC Communication is IIC I2C interface, only needs 2 IO ports Compatible with MMDVM, Pi-Star, and compatible with Raspberry pi. Self-luminous design the OLED display module is self-luminous, so that no backlight is required It features high contrast, bright and crisp dots, which is convenient for you to read tiny fonts. Create fonts there are no fonts embedded in the OLED controller, so users can use the font generation software to create the fonts.

Driver IC SSH1106.Resolution 12864. Four square holes are easy to install. Ultra-low power consumption full screen lit 0.08w. The IIC address can be changed,it is convenient to use with different machines. Supports many control chip fully compatible with Arduino 51 series,msp430 series , stm322 CSR IC etc.