Top 8 Best Kreg Crosscut Saw Guide

Quickly and accurately crosscuts up to 8 203mm wide. Also makes precise 45 cuts. Cutline indicators show exactly where your saw will cut. GripMaxx eliminates slipping and holds the guide in place. Take the guide anywhere your projects take you.

Make rip cuts and crosscuts up to 24 Wide. Cut multiple pieces to the same size With just one setup. Use the oversize edge guide for precise control throughout the cut. Eliminate need for marking, measuring, and layout lines. Take your saw to the material instead of having to take your material to the saw.

Crosscut up to 12 wide 305mm and make a variety of miter cuts from 0 to 45. MDF base and backboard act as sacrificial surface for splinter-free cutting. A kerf line you cut into the MDF base shows exactly where your saw will cut. Material support wings with detachable blocks add offcut support for long pieces. Works with left- or right-blade circular saws.

Includes full manufacturer warranty.

Rip, crosscut, and make angled cuts up to 50 Long in plywood, MDF, and panels. Simply align the guide Track with your marks to make accurate cuts. Hold track in place without clamps thanks to anti-slip guide strips. Prevent splintering with anti-chip strips that support material during the cut. Begin cuts easily with a starting block that the supports saw and allows normal blade guard operation,.

Break down panels and plywood easily and quickly with cutting capacity up to 100. Splinter-free cuts with tear-out protection from anti-chip guide strips. Make the cuts you need anywhere by taking your saw to the workpiece instead of bringing the workpiece to a fixed saw location. Easily attaches to your left-blade or right-blade circular saw, and removes easily. No clamps needed thanks to Anti-slip guide strips that keep the track in place through the entire cut.

Crosscut and rip cut material up to 8 feet 244cm. Aluminum guide rail leads cuts precisely along a straight line. Cutline indicators help position cuts perfectly. Built-in clamping with GripMaxx secures rail to material. Works with left- and right-blade circular saws, as well as some jigsaws and trim routers.

No more c-clamps when trying to secure a straight edge to your large or small wooden panels Cut large panels, small panels, rout straight dados and more ProGrip Straight Edge Guides are not only great straight edge guides, they are super easy to align and even easier to clamp into place. Made from extruded aluminum and with the extra wide 2-316 inch tube rail, the ProGrip Straight Edge Guide Clamps are robust guides that are made for everyday workshop or contractor use.. Cut straight, true lines with circular saws, routers, trim routers, jig saws and many other power tools you probably own. These clamps are ideal for cutting large sheets of plywood in half with a 50 straight edge guide. Each clamp is identified by the maximum clamping distance between jaws. Another great application for these clamps is cutting dado slots for bookshelves. The alignment and cutting process for dados is so much easier than ever before with the ProGrip Straight Edge Guides.. Each clamp rail is manufactured with a low profile to make guiding your power tool along the edge much easier. The low profile has also been designed with guide accessories in mind. The clamp rails accept many different accessories sold separately or can create your very own jigs and fixtures to use with the ProGrip Straight Edge Guides. Each ProGrip Straight Edge Guide has the exact same profile regardless of length.. How does it work Each ProGrip Straight Edge Guide Clamp has one adjustable jaw and one fixed jaw. The fixed jaw typically will go against the edge of the board closest to you. Once you place the clamp on your board with the fixed jaw over the end, the adjustable end gets drawn in against the opposite side of the board. Once set and aligned, you secure the clamp by simply locking it down with the 3 position lock lever.. The lock lever on each clamp can be secured into one of three positions, each position provides varying amounts of pressure. Depending on your project or application, you may need to apply more pressure by securing the lock lever to the appropriate position. Once secured, the ProGrip Straight Edge Guide Clamp is designed to have zero side to side play with minimal deflection to provide you with the ideal straight edge to make clean, smooth cuts every time.

Factory Calibration. Guaranteed out of the box to .003 accuracy of 6-inches. Gauge head is CNC machine perfectly square to the bar and table no stampings. Vernier scale allows fast, 110th-degree angle adjustments. Our extremely straight 24 inch 610mm anodized-aluminum bar is 38 inch9.5mm thick by 34 inch19mm wide and features five bar adjusters that you can use to eliminate play in the miter slot with the turn of a screwdriver. Microadjuster allows additional angle adjustment to 1100th degree. Positive stops at 0, 10, 22-12, 30 and 45-degrees limited lifetime warranty.

CUTS Make rip cuts and crosscuts up to 24 wide Cut multiple pieces to the same size with just one setup Prevent splintering with anti-chip strips that support material during the cut. GUIDE Use the oversize edge guide for precise control throughout the cut Eliminate need for marking, measuring, and layout lines Hold track in place without clamps thanks to anti-slip guide strips. EASY SAWING Take your saw to the material instead of having to take your material to the saw. VERSATILE Rip, cross cut, and make angled cuts up to 48 long in plywood, MDF, and panels Simply align the Guide Track with your marks to make accurate cuts. BUNDLE INCLUDES Kreg KMA2700 Accu-Cut 48-Inch Circular Saw Guide Track System.