Top 8 Best L298n

L298N as main driver chip makes strong driving abilitysmall heatingstrong anti-interferencelow calorific value. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. Dual-channel H-bridge driver working mode creates higher working efficiency. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage. Large capacity filter capacitance, afterflow protection diode, more stable and reliable.

Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability,low calorific value and strong anti-interference ability.. This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage of the voltage stabilizing chip,please use an external 5V logic supply when using more than 12V driving voltage.. Using large capacity filter capacitor,this module can follow current to protect diodes,and improve the reliability.. Dual-channel H-bridge driver working mode creates higher working efficiency. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.

Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip.Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. High working power to 35v,large current can reach 3A MAX and continue current is 2A, power to 25w.. Large capacity filter capacitance,afterflow protection diode, more stable and reliable..

1.When you are driving voltage above logo for the 12 v input, can actually accept input range is 7 to 12 v for 7 v to 12 v, can make to onboard power supply 5 v logic, when using the onboard after 5 v power supply, interface of 5 v The power supply does not input voltage, but can yield 5V voltage for external use.. 2.The chip manual proposes to support 35V, but according to the book When the maximum voltage is applied to the maximum voltage of 298 conservative applications to 24V, for example, the motor with a rated voltage of 18V shall be driven. 3.Great for for Arduino DIY Smart Car Robot Power UNO MEGA R3 Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits. 4.No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use. 5. Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient.

Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip.Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. High working power to 35v,large current can reach 3A MAX and continue current is 2A, power to 25w.. Large capacity filter capacitance,afterflow protection diode, more stable and reliable..

This is a good parts kit for an Arduino and raspberry pi based RC car project. It not only comes with 4pcs wheels and motors, but also 2pcs motor drive modules and 60pcs jumper wires, which are very useful accessories for your project.. Motor Drive Controller L298N used as the main driver chip. It has the strong driving ability, low calorific value and strong anti-interference ability.. TT Motor The motor is a two-axis motor with a reduction ratio of 148, which has strong anti-interference ability.. Smart Car Wheels The wheels are made of high-strength plastic and the tires are made of durable black rubber.. To avoid damage the voltage stabilizing chip of Motor Drive Module, please use an external 5V logic supply when using more than 12V driving voltage..

Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects. Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient. No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use. External size 434327mm 1.691.691.06 inch, voltage 5V-35V, drive current 2A Max single bridge. Great for Arduino DIY Smart Car Robot Power UNO MEGA R3 Mega2560 Duemilanove. If driving voltage is more than 12V, please use external standard 5volt TTL outputs to switch the H-bridge circuits.

L298N has such characteristics as strong driving ability, low calorific value and strong anti-interference ability. L298N as main driver chip makes strong driving abilitysmall heatingstrong. Dual-channel H-bridge driver working mode creates higher working efficiency. Using large capacity filter capacitor, this module can follow current to protect diodes, and improve the reliability. This module can use built-in 78M05 for electric work via a driving power supply part. But to avoid the damage of the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.

The L298N driver module, using L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface, you can chip circuitry to 5V power supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential.. Terminal driver part of the supply area VMS 5V 35VDrive part of the peak current Io 2A Bridge. Logical part of the terminal power supply range Vss 4.5-5 .5VLogical part of the operating current range 0 36mA. The control signal input voltage range 4.5-5.5V low 0V highMaximum power consumption 20W. Driver Board Size 55mm 60mm 30mm.

This is a good Motor Drive for an Arduino and raspberry pi based RC car project. It comes with 6pcs motor drive modules and 60pcs jumper wires for different interfaces, which can meet your project needs.. Motor Drive Controller L298N used as the main driver chip. It has the strong driving ability, low calorific value and strong anti-interference ability.. Jumper Wire Kit 20cm Jumpers, Female to Female, Male to Male, Male to Female each 20Pin.. NOTE Suitable for DC motors in smaller projects, but not for prototyping. Not recommended for stepper motors..