Top 8 Best Makerfocus

Application Internet of things terminal controller Stem education product DIY creation Smart home equipment. Improvement Further enhances the functions of the original generation of cores. The MCU is an ESP32 model D0WDQ6-V3 and has dual core X t e n s a 32-bit 240Mhz LX6 processors that can be controlled separately WiFi is supported and it includes an on board 16MB Flash and 8MB PSRAM, a 2.0-inch integrated capacitive touch screen, and a built-in vibration motor. Power Supply The battery capacity has been upgraded to 3.7V390mAh, which can power the core for much longer than the previous model. The power supply is managed by an AXP192 power management chip, which can effectively control the power consumption of the base and a built-in green LED power indicator helps to notify the user of battery level. More Function Built-in PDM microphone, power indicator, 6-axis IMU, vibration motor, I2S codec, amplifier, speaker, RTC, power button, reset button, 10 x RGB LEDs. Note The development platform and programming language supported by M5Stack Core2 A r d u i n o, UIFlow using Blockly, MicroPython language.

Note The battery overcurrent protection is not a panacea, do not continue to charge and discharge the current and voltage with a large current beyond the range, otherwise the protection board will be damaged and invalid. When using for the first time, please charge and activate the protection board first. 1000mAh The recommended charging current is 0.2A, the maximum is not more than 1A The discharge current is recommended 0.55A, and the maximum is not more than 3A. Over-discharge protection When the battery is about to run out and the voltage is as low as 3.0V, the protection board will also be turned off and can no longer be discharged, forming an over-discharge protection effect. Overcharge protection When charging the battery, when the voltage reaches the highest battery voltage 4.2V, the protection board will automatically power off and shut down, indicating that it will not continue to charge when fully charged. form an overcharge protection. Short circuit protection When an accidental short circuit occurs, the protection board will automatically shut down within a few milliseconds and will not be powered on again. Note that the cell is short-circuited not through the protection board. The protection board will also fail due to continuous high current, or the components are heated and damaged.

User Manual You can contact us by order number and we will provide you with instructions. OLED display, no need backlight, self-illumination, Display Color White. Plz note These I2C OLED Display Module comes without pin headers.. The display performance is better than the traditional LCD display, also lower consumption IIC I2C communications simplifies connections.. Use with Ar duino, ESP8266, ESP32, STM32, etc 3.35v Power Operating temperature -40 - 85 Resolution 128 x 32.. We have a Strong After-sales Service Team As long as you have any questions about the product, we will resolve your issue immediately if received your email, your satisfactory purchase experience is our greatest hope How to email us Plz click MakerFocus and click Ask a question to email us Looking forward to your consultation.

Upgrade Version M5Stack Tough ESP32 adopts O-ring containing M12 waterproof connector, anti-ultraviolet shell design, comprehensive resistance to solid objects, dust, sand and water immersion. Powerful Configuration ESP32 IoT 2-inch LCD capacitive multi-touch screen, NS4168 16bits I2S power amplifier 1W speaker, TFC card slot, AXP192 power management chip BM8563-RTC clock. Strong Scalability M5 stack tough equipped with programmable expansion board, integrated 12v-5V flexible DCDC converter. Flexible power supply, RS485 conversion circuit, ports A, B, C3x Grove expansion interface, easy access to M5Stack software and hardware system, plug and play sensor expansion. Low Code Development Support UIFlow graphical programming platform, script-free, cloud push, fully compatible with mainstream development platforms such as Ard uino, ESP32-IDF, etc., execute dual-core processors on Free RTOS, run multitasking, and have better performance. Applications Applied to IoT controllerdata acquisitiondisplay terminalsequence controller.

Innovative Design Timer camera is a camera module based on ESP32, integrated 8MB PSRAM, 3MP pixel camera ov3660, DFOV 66.5, can take photos with a maximum resolution of 2048x1536. Function LED status indicator and reset, sleep and wake up function, support UIFlow graphics programming, image transfer firmware and image data acquisition. Supported Platforms ESP-IDFArduinoUIFlow 8-bit10-bit RAW, RGB and YCbCr output, Compression, UIFlow - Media Transfer, UARTTimer, Ar duino IDE, TimerFolderPusher, Timer Amazon S3 FolderPusher. Ultra-low Power Consumption In sleep mode, the current consumption of the whole machine is only 2A, and the timed photo function is turned on and the battery can work continuously for more than 1 month. Widely Applications Suitable for various internet of things applications, industrial wireless control, WiFi cameras, remote monitoring, media transmission, smart device image transmission.

Support Ar duino Development Environment Supports Ar duino version of ESP32 LoRaWAN protocol routine. This is a standard LoRaWAN protocol that can communicate with any gatewaybase station running the LoRaWAN protocol. Easy to Use With good RF circuit design and low-power design sleep current 10A, it is convenient for IoT application vendors to quickly verify solutions and deploy applications. Perfect Design Integrated WiFi, LoRa, Bluetooth three network connections, onboard WiFi, Bluetooth dedicated 2.4 GHz metal 3D antenna, reserved IPEX U.FL interface for LoRa use integrated CP2102 USB to serial port chip, convenient for program downloading, debugging information printing. Power Supply Onboard SH1.25 battery interface, integrated lithium battery management system, you can also use the Type-C interface to power the development board, the interface with complete ESD protection, short circuit protection, RF shielding and other protection measures. OLED Display Onboard 0.49-inch 6432 dot matrix OLED display, which can be used to display debugging information, battery power and other information.

Support Ar duino Development Environment Support ESP32 LoRaWAN protocol Ar duino library, this is a standard LoRaWAN protocol that can communicate with any LoRa gateway running the LoRaWAN protocol. Easy to Use With good RF circuit design and low-power design, ESP32 development board is the best option for smart cities, farms, homes, industrial control, house security, wireless meter reading and IoT developers. Perfect Design Integrated WiFi, LoRa, Bluetooth three network connections, onboard WiFi, Bluetooth dedicated 2.4GHz metal spring antenna, reserved IPEX U.FL interface for LoRa use. Integrated CP2102 USB to serial port chip, convenient for program downloading, debugging information printing. Power Supply Onboard SH1.25 battery interface, integrated lithium battery management system You can also use the Type-C interface to power the development board, the interface with complete ESD protection, short circuit protection, RF shielding and other protection measures. OLED Display Onboard 0.96-inch 12864 dot matrix OLED display, which can be used to display debugging information, battery power and other information.

Note If you use UPS to power Raspberry Pi3b3B while charging, please make sure that the input power is not less than 2.5A. Recommended use 3V 2.5A power supply The document link is obtained in the Product guides and documents. The link to the assembly video is available on the product page, Two power supply modes outdoor portable type and indoor UPS power supply mode 1 As an outdoor portable power supply, the main board is powered by a lithium battery. The maximum external power supply capacity is 5.1V. 2.5A. 2 As an indoor UPS power supply mode the UPS power supply interface is connected to an external 5V power supply, the power supply requires 5V 2A-3A, and the maximum output current can reach 5V 3A. 42LED are designed to show the status of battery power, charge or discharge1 4 Battery power LEDs Used to show the current battery voltage and power. 2The function of the Power LED is to display whether the UPS is supplying power to the Pi, and the LED is on it means the output is 5V. LED off Indicates that there is no voltage at the output. 3 Charging indicator LED When the UPS is externally charged via the TYPE-C USB interface, the Charge LED starts to work. The UPS has overcharge and overcurrent protection functions When the UPS externally outputs about 4A, the UPS will consider the external circuit to be in a short-circuit state and automatically cut off the output. The lithium battery board that comes with the UPS has an overcharge and overdischarge protection board. Prevents the battery from being overcharged and overdischarged when the external circuit is abnormal, thereby reducing the possibility of damage to the battery. Two output modes In addition to the regular output via the USB port, the V3P output interface adds an LC filter, the ripple is about 20mV under no-load condition, and the ripple is about 50mV when Raspberry Pi 4 is connected.

Variety of Styles There are three soldering methods SMT, DIP, flying leads M5Stamp C3U resistance also provides excellent heat resistance, plastic housing can maintain higher operating temperature, peak temperature 230. Scope of Application small size, powerful functions, suitable for a variety of IoT scenarios DIY, prototyping, industrial automation, smart home, portable equipment, medical equipment, consumer electronics. High Integration M5Stamp C3 includes 5V-3.3V DCDC design, GPIOx14 USB C port RGB LED color programming 1, Reset button1, button 1 3D antenna for stable and reliable wireless communication. Excellent Performance The M5Stamp C3U is based on a 32-bit RISC-V microcontroller with a maximum clock frequency of 160 MHz. With 400 KB of internal RAM and 4 MB of flash, it can facilitate many different use cases, including connected devices. Safe and Secure The M5Stamp C3U features an ESPRESSIF ESP32-C3 RISC-V MCU with Wi-Fi 5 LE connectivity for home appliances and industrial automation. Combines RSA-3072 based Secure Boot and AES-128-XTS based flash encryption.

Note TF-Luna module comes with UART and I2C interface, the default is UART, if you need to use I2C interface, please set it yourself.. TF-Luna TF-Luna is a single-point ranging LiDAR, based on TOF principle. With unique optical and electrical design, it can achieve stable, accurate and highly sensitive range measurement.. Product Characteristics The product is built with algorithms adapted to various application environments and adopts multiple adjustable configurations and parameters so as to offer excellent distance measurement performances in complex application fields and scenarios.. Extreme Cost Performance Low-cost ranging LiDAR module, with 0.2-8m operating range. TF-Luna has a highly stable, accurate, sensitive range detection.. Slim Figure Yet Big Skill The product is built with algorithms adapted to various application environments and adopts multiple adjustable configurations and parameters so as to offer excellent distance measurement performances in complex application fields and scenarios..