Top 8 Best Motor Driver

L298N as main driver chip makes strong driving abilitysmall heatingstrong anti-interferencelow calorific value. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. Dual-channel H-bridge driver working mode creates higher working efficiency. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage. Large capacity filter capacitance, afterflow protection diode, more stable and reliable.

Support motor voltage from 7V to 35VDC. Maximum current up to 80A peak 1 second, 30A continuous, each channel. On board MOSFETs are switched at 18 KHz for quiet operation. Regenerative Braking. Accepts RC Radio Control, PWM, Analog voltage, UART data.

Package 2 pcs.

5V isolate with MCU, and effectively protect MCU 5V power indicator on board.. Voltage indication of motor driver output end can solder heat sink.. Just need four lines from MCU to driver module GND. 5V. PWM1. PWM2 isolation chip 5 V power supply can share with MCU 5 V.. Able to reverse the motor forward, two PWM input frequency up to 25kHZ two heat flow passing through an error signal output.. Isolated chip 5V power supply can be shared with the MCU 5V, can also use the on-board 5V supply the supply voltage 5.5V to 27V..

Use of imported original chip, built-in low on-resistance MOS switch. Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor. Dual 1.5A 2, the peak current to be 2.5A, built-in thermal protection circuit, do not be afraid motor stall burned, automatic recovery after the temperature dropped. Minimal heat, no heat sink, small size, low power consumption, is ideal for battery powered. Small size, light weight, low standby current, is the ideal choice for your car model.

Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects. Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient. No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use. External size 434327mm 1.691.691.06 inch, voltage 5V-35V, drive current 2A Max single bridge. Great for Arduino DIY Smart Car Robot Power UNO MEGA R3 Mega2560 Duemilanove. If driving voltage is more than 12V, please use external standard 5volt TTL outputs to switch the H-bridge circuits.

Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability,low calorific value and strong anti-interference ability.. This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage of the voltage stabilizing chip,please use an external 5V logic supply when using more than 12V driving voltage.. Using large capacity filter capacitor,this module can follow current to protect diodes,and improve the reliability.. Dual-channel H-bridge driver working mode creates higher working efficiency. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.

Widely used in the garden, agriculture, geophysical exploration, construction and more. Portable and lightweight for easy handling and convenient transport It is powerful enough for most heavy-duty job applications, yet lightweight for effortless control. Displacement 32.7CC This is a EPA approve product beware of non epa engines Engine Type single cylinder, air cooling, 4-Stroke. Max Power and Speed 900w 1.2HP and 9000rmin Max torque and speed 1.45N.m and 5000rmin. Piling Heads Size 55mm, 69mm with Carrying Case.

DROK DC motor driver input voltage range is DC 6.5V-27V, can be input DC 12V or 24V, rated output current of each port is 7A, total output power is 160W.. STRONG DRIVE the motor controller board adopts dual H bridge, can drive two DC motors at the same time.. FORWARD and REVSERSELY ROTATE the IN1, IN2IN3, IN4 port can control forward or reverse motor rotation.. PWM SPEED CONTROL enable signal terminal ENA input PWM can regulate speed, PWM frequency range 0-10KHZ.. UNDER VOLTAGE PROTECTION the motor driver module is with under voltage protection to prevent instantaneous large current from damaging the module..

DC Brush motor Driver, not for brushless motor. Input Voltage Motor 7 - 45VDC. Dual Channels, it can drive two brush motor independently, or mixed.. Operating modes RC RC servo signal, Analog, PWM, simplified and packetized UART.. Temperature feedback for current limit and prevent overheating of MOSFET..