Top 8 Best Peachtree Woodworking Supply

Clamping panels can certainly be a challenge. Especially when we try to use everyday pipe clamps or bar clamps. While these types of clamps work fairly well on certain glue up projects, the one thing they dont do at all is apply pressure from the top and bottom of the panels during glue up. In fact, with all the pressure being applied on both sides, bar and pipe clamps will almost certainly bow, buckle or rack your panel glue up project.. Lets make racked panel glue ups a thing of the past The uniquely designed 4 way pressure solves this age old issue by applying pressure to all four sides of your panel glue up. With a simple turn of the rotating clamp handle, all four sides of the clamp will draw inward at the same time. This provides equal pressure on to your panel and prevents bowing, buckling, or racked panels.. Build any length clamp with the durable plastic bars with 4 notches for maximum adjustability to handle a variety of stock widths. Clamp can be used for boards up to 6 inches in thickness by simply adjusting the clamp width capacity with the appropriate number of notches. Turn the handle clockwise to tighten the clamp and turn the handle counter clockwise to release pressure. The 4 way pressure clamp is equipped with side pressure pads to prevent damaging your stock.. Now you can confidently glue up wide boards, shelving, table tops, and more up to 6 thick. To setup the clamps simply attach the clamp to any length 2 x 2s 2 x 4 ripped in half with the the wood screws that are provided, apply wood glue to your project, set the clamps on to your panel boards and turn handle to tighten the clamp on all four sides. We recommend that you place a 4 way pressure clamp every 12 to 18 for best results.. This clamp package comes with two full 4 way pressure clamp assemblies. Includes 2 each rotating handle assemblies, 2 each tailstock assemblies, 4 each side pressure pads and 12 each 4 notch bars. Together, this setup will allow you to create two 4 way pressure clamps. More than one clamp is generally recommended for any project over 12 in length. Wood is required for setting up the clamp. Wood is NOT included..

The smaller diameter 1-316 O.D. Outside diameter flexible dust collection power tool hose moves freely when connected to your power tools and vacuum. This gives you the ability to plug into different tools to add dust collection at a moments notice. The hose and its specialized fittings work with multiple power tools, workshop vacuums, jigs and other tools around your woodworking shop or work shop.. The small rubber fitting threads on to the end of the hose and is ideal for connecting random orbital sanders, palm sanders, biscuit joiners or any other power tool with smaller dust collection ports. The small thread-on rubber fitting has a 1 inch I.D. with a 1-316 inch taper up to 1-14 inch O.D. This kit will also work with popular tools like the K4 and the K5 Pocket Hole Jig. Using this hose with your tools will keep your shop cleaner and can be quickly coiled up for easy storage. The large thread-on rubber fitting has a 1-12 inch I.D. with a 1-1316 inch O.D. which works on many other power tools. The rigid plastic vacuum Plug-in Adaptor has a 2-14 inch taper up to 2-516 inch O.D. The adaptor is designed to plug into most standard workshop vacuum ports. The Plug-in Adaptor conveniently threads onto the power tool hose so it will never slip off. Included inside the box 1 each ten foot long 1-316 inch O.D. small diameter flexible hose, 2 each small flexible rubber thread-on fitting, 2 each large flexible rubber thread-on fitting and 2 each Plug-in Adaptor shop vacuum that will allow you to connect the hose to most commercial or residential workshop vacuum ports.. IMPORTANT CHECK YOUR POWER TOOL PORT DIMENSIONS Before placing an order, please check the inner and outer I.D. and O.D. diameter of your workshop vacuum ports and power tool ports to make sure the hose and fittings will properly fit and work for your needs. THE I.D. AND O.D. ON THE RUBBER END FITTINGS AND HOSE ARE APPROXIMATE SIZES AND MAY SLIGHTLY VARY..

Since many of us have to move machinery and workbench or just tables around to get work done, being able to maneuver your work bench or work shop tables when needed is an absolute must. The other challenge is making sure that the wheels or casters you attach wont raise the working height of your bench or table.. The workbench casters solves this issue in spades Since these casters are designed to be installed on a flat base workbench, table, cabinet, stand or machine and with its lever cam raising and lowering mechanism, you can move things all around your shop with ease. The casters can be raised and lowered at your leisure and that means your working height will always be the same when the casters are not engaged.. This set of 4 casters work by simply pushing down on the pedals to raise your workbench off the floor. Once elevated you can move your bench, table or machine as desired, then lift up on the pedals to disengage and your workbench, table, cabinet, stand or machine sits firmly on the floor at its original working height.. Each lift pedal is ribbed and textured to provide extra grip when foot pressure is applied. The 2-38 urethane casters are rated for 210 lbs of capacity, which means all four together give you a total weight capacity of 840 lbs. The casters will work on most workbenches, stands, tables, cabinets and lightweight machinery with flat bases.. The workbench casters include 4 workbench caster assemblies with assembly hardware, all the necessary mounting hardware, full instructions and an installation template for quick and easy mounting of the workbench casters to a standard flat base surface..

Sharpen chisels, gouges, bowl gouges, spindle gouges, carving tools, wood turning scrapers, parting tools, block plane irons and more with the PRO GRIND Sharpening System With 3 primary methods of sharpening, youll be able to precisely hone each tool to your exacting specifications regardless of the tool you are sharpening. The PRO GRIND Sharpening System includes a vast collection of unique setup tools, jigs and accessories that most sharpening systems force you to purchase separately. The included and versatile Multi-Grind Jig will correctly shape the edge on bowl gouges, side grinds aka Ellsworth grind, Liam ONeil grindIrish grind or fingernail grinds for spindle work and detailing. Not only will it correctly shape your tools, you will also be able to repeat the process to produce consistent results every time. The Multi-Grind Jig is designed to be used with the included Multi-Grind arm on the PRO GRIND Sharpening System and will accept tools up to 1.125 in diameter.. The PRO GRIND Tool Rest Bar attachment offers you the best possible way to achieve a precise edge to your bevels without taking of too much material off of your tool. After all, we need our tools to last a long time, so why would you want to take off to much at a time The Tool Rest Bar is ideal for sharpening curved, even bevel edges that are typically used on spindle and roughing gouges.. The large, 3 x 5 slotted platform is the ideal way to sharpen flat edged tools like wood turning skews, chisels and hand plane irons. The platform has a slot milled horizontally through it so it can accept the included tool holder. The tool holder is designed to keep your tools at the correct angle while being able to slide side to side during the sharpening process.. The PRO GRIND Sharpening System also comes with a number of setup jigs and accessories to help in the setup process to sharpen your tools to the proper and repeatable angles. From the built-in projection gauge on the Multi-Grind arm to the Magnetic Micro Bevel setup block youll be able to achieve consistent repeatable angles and produce excellent results each and every time you use the PRO GRIND Sharpening Jig system..

When setting up our dust collection or filtration systems we tend to have a lot of moving parts during this process and trying to figure out what type of line, piping or hose to use can be challenging. Dust collection hoses need to be not only long enough, but it must be durable, flexible and sturdy enough, so it wont completely collapse in use. It must also perform under the constant use and abuse of an everyday workshop environment. This PVC hose checks all of those boxes and more. Typically, PVC hose works best as a dust collection hose for woodworking applications where dust and chips from cutting, milling or sanding wood is a problem. This heavy-duty hose will stand up to small and large chunks of wood without getting punctured as well as handle the smallest of saw dust without leaking. PVC hose can be used as a primary line or can be plugged into and out of machinery as needed.. PVC Hose depending on diameter can be used with dust collectors, shop vacuums, industrial vacuum systems, lawn tractor leaf catchers and a whole lot more Simply make sure both ends of the hose are secured with hose clamps and your ready to go. The PVC hose flexes enough to weave in and out of shop machinery or table legs without kinking. Its also sturdy enough that it wont flatten out when the dust collector is turned on. The hose has a compression ratio of 3 1.. This PVC hose is clear which allows you to see whats going on inside the hose while the dust and debris are flowing through it. Not only can you see the dust and debris, you can also see if any build up or blockage has occurred. Being able to see this makes fixing any suction issues with the hose much easier than typical opaque hoses.. While PVC Hose can be used on other machinery or devices it has been designed for dust collection purposes. The hose temperature range is -20 F to 165 F which is ideal for indoor use like in a woodworking or workshop environment. The clear hose wraps around a black carbon steel wire helix that reinforces the hose to keep it from kinking and is capable of an electrostatic discharge when properly grounded at both ends of the hose..

Easily locate and drill pen blank centers and Drill through the exact center of your pen blanks with this simple but effective Pen Centering vise. By far one of the best selling pen vises available, this jig will be a go to tool when turning your pens.. The jaws on the drilling center move in and out simultaneously to insure precision center drilling of your blanks each and every time you use the vise.. Just set up the vise once and drill all of your blanks in the exact center. There is no need to change the setup regardless of the blanks size or shape.. Holds blanks up to 1-12 square. The pen center vise includes a scrap board piece of mdf. It measures approximately 2 by 14.. The scrap piece can be flipped, slid and reversed to get numerous uses out of a single piece. When you use up all of the surface, simply cut another piece out of 14 thick stock. Wooden base is removable and replaceable. If you need a larger base to clamp the vise to your drill press, simply remove the wooden base and replace it with a base made to your exact specifications.

Making repetitive cuts on your table saw is a pretty straight forward process. Set your fence and feed each stock piece through the blade to achieve the same size each and every time. What if you need a series of narrow cuts that are about an 2 inches or less in width Doing this can get tricky since you cant get your hands safely between the blade and the fence. You could always reverse measure and keep the off fall piece, but without a guide of some sort that can be inaccurate.. The Thin Rip Jig acts kind of like a third hand behind the blade or cutter. With the saw unplugged simply measure from the outside of of the blade toward the tip of the guide roller Thin Rip Jig for the width cut you want to make. Once set, secure the Thin Rip Jig simply by rotating the large, easy to grip star shaped knob. After your first cut, reset your stock behind the blade and slide the fence over so your stock piece is touching the guide roller on the Thin Rip Jig. Lock the fence.. Making your thin rip cuts in this fashion allows you to cut wider boards down without getting your fingers in harms way by keep them away from the blade or cutter.The Thin Rip works much like a feather except that it doesnt exert spring like pressure against the board. This means it can be used to make accurate, repetitive cuts since its essentially just holding its spot once it is secured.. The Thin Rip Jig has a roller guide bearing on the tip to make feeding your stock through an easy and smooth moving process. The free rotating bearing is made from high quality materials for extended workshop use. The jig fits directly into most any standard 38 x 34 miter slot. The body is made from a solid piece of aluminum and is adjustable inward and outward from your fence depending on the width of your stock.. The jig can be used on other workshop machinery like router tables with fences and band saws for re-saw applications. In certain cases, when working with larger or longer stock on table saws or router tables, we recommend using two thin rip jigs behind the blade or cutter for extra stability when feeding your stock through..

When you need to finish sand the inside of your wood turned bowl it can be a challenge to keep the wood from showing scuff marks. Using a piece of hand held sandpaper can also be somewhat dangerous. Our bowl sander essentially fixes this issue by having a dual bearing, smooth rotating head that spins with the rotation of the bowl while the bowl is rotating on the lathe. The 9 inch long handle also helps keep your hands out of harms way.. The head assembly is completely adjustable so it can be set to any angle that you need depending on the size and curve of your project. Unlike most other bowl sander head assemblys, our bowl sander has two steel bearings to provide you with super smooth mandrel rotation while sanding on your lathe. This also helps to reduce the chance of marking your wood since the sander will be rotating without hanging up or catching like so many other brands do.. Its all about the pressure, or more like, its all about the light pressure and consistent technique. When sanding with the 2 inch bowl sander, applying too much pressure will likely produce some unsightly results. By applying light pressure and consistently moving the sander, you will achieve the results you are looking for and in a fraction of the time it typically takes when hand sanding your project.. The head assembly is also capable of accepting other size sanders as long as the mandrelshank size is 14 inch in diameter. Please be aware however that some manufacturers say 14 inch in diameter when in actuality the diameter is either smaller or slightly larger. 3 brass bushings of varying depths are included to make fitting sanders with different length mandrelsshanks easy.. We have included the most common diameter sanding head with the bowl sander. This sander head is made from a foam material that gives just enough to provide you with wonderful looking results each time you sand your projects. This 2 head size works well on most bowl turning projects since it can work with larger or smaller work pieces. Also included 10 ea. 80 grit, 10 ea. 120 grit, 10 ea. 150 grit and 10 ea. 220 grit hook and loop sanding discs..

Ideal for sawdust collection and fume ventilation in woodworkng applications. Good abrasion and tear resistance. Excellent chemical resistance. Extremely flexible.

When setting up our dust collection or filtration systems we tend to have a lot of moving parts during this process and trying to figure out what type of line, piping or hose to use can be challenging. Dust collection hoses need to be not only long enough, but it must be durable, flexible and sturdy enough, so it wont completely collapse in use. It must also perform under the constant use and abuse of an everyday workshop environment. This PVC hose checks all of those boxes and more. Typically, PVC hose works best as a dust collection hose for woodworking applications where dust and chips from cutting, milling or sanding wood is a problem. This heavy-duty hose will stand up to small and large chunks of wood without getting punctured as well as handle the smallest of saw dust without leaking. PVC hose can be used as a primary line or can be plugged into and out of machinery as needed.. PVC Hose depending on diameter can be used with dust collectors, shop vacuums, industrial vacuum systems, lawn tractor leaf catchers and a whole lot more Simply make sure both ends of the hose are secured with hose clamps and your ready to go. The PVC hose flexes enough to weave in and out of shop machinery or table legs without kinking. Its also sturdy enough that it wont flatten out when the dust collector is turned on. The hose has a compression ratio of 3 1.. This PVC hose is clear which allows you to see whats going on inside the hose while the dust and debris are flowing through it. Not only can you see the dust and debris, you can also see if any build up or blockage has occurred. Being able to see this makes fixing any suction issues with the hose much easier than typical opaque hoses.. While PVC Hose can be used on other machinery or devices it has been designed for dust collection purposes. The hose temperature range is -20 F to 165 F which is ideal for indoor use like in a woodworking or workshop environment. The clear hose wraps around a black carbon steel wire helix that reinforces the hose to keep it from kinking and is capable of an electrostatic discharge when properly grounded at both ends of the hose..