Top 8 Best Raspberry Pi Battery Pack

Raspberry Pi UPS Uninterruptible Power Supplies module, compatible with Raspberry Pi 4, 3 and all Model BB series. Also suitable for other boards powered by USB 5V3A such as Banana PiRock PiLibre Computer Board.. Pass-through charging technology, battery pack included. It can charge Raspberry Pi and battery pack simultaneously.. Battery protection technology, support over chargedischarge protection, balance charging and over heating protection.. UPS module output 5V3A, battery charge 5V2A MAX.. Battery capacity 7.4V 2000mAh. Battery life 3-4 hours..

PiSugar 3 adds a software watchdog function. When the function is turned on, the dog needs to be kicked regularly, which can effectively prevent the Raspberry Pi from crashing and improve the reliability of the system.. PiSugar 3 provides hardware battery protection like never before, limiting battery voltage to nearly 80. When charging protection is turned on, the battery cycles life can be improved.Set up quadruple overvoltage protection function, overcurrent protection function and undervoltage protection function to ensure the safety of the Raspberry Pi, PiSugar as well as the lithium battery.. PiSugar 3 continues to use the pogo pin design to connect with Raspberry Pi from the back. In this way, it does not occupy the GPIO, and is compatible with other GPIO devices.. PiSugar 3 has full UPS functions and can set up multiple awakening methods to meet various unique project needs.. PiSugar 3 communicates with the Raspberry Pi through the I2C interface and is compatible with most I2C devices. In addition, the I2C communication address can be customized to avoid I2C address conflicts..

Note If you use UPS to power Raspberry Pi3b3B while charging, please make sure that the input power is not less than 2.5A. Recommended use 3V 2.5A power supply The document link is obtained in the Product guides and documents. The link to the assembly video is available on the product page, Two power supply modes outdoor portable type and indoor UPS power supply mode 1 As an outdoor portable power supply, the main board is powered by a lithium battery. The maximum external power supply capacity is 5.1V. 2.5A. 2 As an indoor UPS power supply mode the UPS power supply interface is connected to an external 5V power supply, the power supply requires 5V 2A-3A, and the maximum output current can reach 5V 3A. 42LED are designed to show the status of battery power, charge or discharge1 4 Battery power LEDs Used to show the current battery voltage and power. 2The function of the Power LED is to display whether the UPS is supplying power to the Pi, and the LED is on it means the output is 5V. LED off Indicates that there is no voltage at the output. 3 Charging indicator LED When the UPS is externally charged via the TYPE-C USB interface, the Charge LED starts to work. The UPS has overcharge and overcurrent protection functions When the UPS externally outputs about 4A, the UPS will consider the external circuit to be in a short-circuit state and automatically cut off the output. The lithium battery board that comes with the UPS has an overcharge and overdischarge protection board. Prevents the battery from being overcharged and overdischarged when the external circuit is abnormal, thereby reducing the possibility of damage to the battery. Two output modes In addition to the regular output via the USB port, the V3P output interface adds an LC filter, the ripple is about 20mV under no-load condition, and the ripple is about 50mV when Raspberry Pi 4 is connected.

Continuous Operation PiSugar2 provides UPS function. It can also shut down safely when the power is too low to avoid data loss and damage caused by sudden power failure.. Elegant Experience Control the module through well-designed graphical web interface. you can get power level and charging status, configure timing power on, custom button functions, low power auto off, etc.. Onboard RTC The onboard RTC makes it possible to obtain real time in any network condition. Timing boot function is also provided.. Multiple Usage Charge through TypeC port compatible with e-mark or microUSB port. PiSugar2 Pro adopts PH2.0 standard battery plug, you can also replace other lithium batteries with 3.7V output on your need.. Extensible Power inputoutput pads are provided on the circuit board, which can be equipped with any 5V standard charging devices, such as solar panels and QI wireless charging..

Easy to Install install in 10 secs. No soldering required. Use small test-pad to supply power, does not occupy any GPIO of Raspberry Pi, can be used both with or without GPIO header.. Perfect Size the standard dimension of raspberry pi zero. You can easily put your prototypes in our open-source 3D print cases. Easy, and graceful.. On-board RTC Provide real-time time for the system, and realize timing startup function. Customer button custom any function with the sh command line. short click double click long click can be set independently.. Visual management interface Check battery status and setting advanced features easily.

UPS Plus is a new generation of UPS power management module which supports OTA firmware upgrade and supports RTC onboard.. There are two INA219 chip onboard to detect batteries voltage and the voltage output from UPS Plus to Raspberry Pi.. Compatible with Raspberry Pi 4B3B3B2BBBAA. Package Inlcudes1 x UPS Plus For Raspberry Pi,4 x M2.5 copper pillar,4 x M2.5 screws,4 x M2.5 long copper stick,4 x M2.5 nuts,1 x Acrylic shield,1 x Instruction.

Intelligent Design UPS for Raspberry PI 4B 3B 3B. Built-in power path management, support side-loading, load high current line compensation function. There are two USB A port power output, and also adds type C output. It provides uninterruptible power for the Raspberry Pi to make your Raspberry Pi still work while moving, and its design is so smart that you can get rid of troubled of a mass wire.. LED Power Display It can use most of the 18 650 batteries and fully comply with the battery characteristics in terms of battery life. The illuminated LED light can quickly show the remain power and support the discharging while charging. You can directly connect to the external power supply for charging. At the same time, the Raspberry Pi will not be turned off.. Multiple Protection Support output overcurrent, overvoltage, short circuit protection input overvoltage, overcharge, overdischarge, overcurrent discharge protection and machine overheat protection. Safe and reliable.. Use and Note This product belongs to the power supply device. Please keep it out of the reach of children. Please strictly refer to the instructions for the UPS product, install the battery first, then connect the UPS to the Raspberry Pi. Please do not reverse the battery. If the battery polarity is reversed, it will directly burn the power management chip of the device. Do not add any Components by yourself.. Package 1 Raspberry Pi UPS 4 M2.5 copper stick 4 M2.5 screws 4 M2.5 long copper stick 4 M2.5 nuts 1 Acrylic shield 1 Instructions. 100 Satisfaction Warranty We always bear in mind that your satisfaction is our priority. For any reason you are unsatisfied with our product at any time, just feel free contact support for exchange or refund. Click MakerHawk-US then Ask a question to contact us..

The Li-ion Battery HAT integrates SW6106 power bank management chip, allows providing 5V regulated power supply to your Pi from a 14500 battery, makes the Pi becomes a portable device.. It will charge the battery as well, supports bi-directional quick charge.. Lithium battery protection circuitry, provides reverse protection, over chargedischarge protection, over current protection, and short circuit protection.. This module can be used as a universal mini power bank, also works with other 5V devices.. This is not a UPS, please note that the Raspberry Pi will restart when you connect it to the Pi. If you need a UPS, please check the UPS HAT..

Support Charge While Discharge It will not affect the output of UPS power supply when external power outage. Note If you use UPS to supply power for Raspberry Pi3b3B when it is charging, please ensure that the input power is not lower than 2.5A. Recommended Use 3V 2.5A power supply. Document link and Assemble video Please get the link from the product description below. Two Power Modes Outdoor portable model and Indoor UPS power Supply mode 1 As an outdoor portable power supply, the motherboard is powered by a lithium battery. and he maximum external power supply capacity is 5.1V. 2.5A. 2As an indoor UPS power supply mode MicroUSB plugs into a normal 5V 2A power adapter, and the external output interfaceUSB-A interface can output a maximum of 5.1V.3A. Battery size 70mm x 41mm x 9.5mm. 42LED are Designed to Show the Status of Battery Power, Charge or Discharge1 4 Battery power LEDs Used to show the current battery voltage and power. 2The function of the Power LED is to display whether the UPS is supplying power to the Pi, and the LED is on it means the output is 5V. LED off Indicates that there is no voltage at the output. 3 Charge charging indicator LED When the UPS is externally charged via the TYPE-C USB interface, the Charge LED starts to work.. The UPS has Overcharge and Overcurrent Protection Functions When the UPS externally outputs about 4A, the UPS will consider the external circuit to be in a short-circuit state and automatically cut off the output. The lithium battery board that comes with the UPS has an overcharge and overdischarge protection board. Prevents the battery from being overcharged and overdischarged when the external circuit is abnormal, thereby reducing the possibility of damage to the battery.. Two Output Modes In addition to the regular output via the USB port, the V3P output interface adds an LC filter, the ripple is about 20mV under no-load condition, and the ripple is about 50mV when a Pi4 is connected.

UPS function The external power supply is disconnected to continuously supply power and obtain the external power status. External power access can trigger boot, suitable for unattended projects. Input and output 5V2A output, 5V2A input. GPIO button It can trigger the device to turn on when it is turned off, and it can be used as a custom button after turning on when the automatic power-on function is turned off. Bottom connection convenient connection method, complete installation in one minute, without affecting GPIO expansion.. Expansion Expansion through wireless charging and solar charging.