Top 8 Best Sleeve Puller

Extra Strength -- Instead of soft carbon steel that strips out easily, we crafted our flange wrench with Stainless Steel. Utilize this tool to handle the insane amount of torque needed to get the job done. Compatible With -- Our pinion yoke wrench is compatible with most Ford, AMC, Dana, and GM yokes. Fits almost all pinion and companion flanges. There are multiple slotted bolt patterns for 14, 516 and 38 fasteners. The center socket hole is 2. Holds The Yoke In Place -- Use the pinion wrench while applying torque. It will help you loosen even the most stubborn pinion nuts. For leverage, grab a 12 breaker bar or 34 drive tool. Tighten Up -- Use the pinion flange tool with a torque wrench to tighten retaining bolts and nuts. Or for setting the bearing pre-load. It can also handle other high torque tasks, like crush sleeves. Additional 12 Square Socket -- Other yoke flange wrenches only have one and round out over time. The problem is, for tight spaces, you might need multiple. To address this, we added an extra 12 square socket. Plus, our stainless steel will prevent any rounding. You'll be able to utilize your pinion depth setting tool for years.

Easily removes compression sleeves. Wont damage walls. Ideal for working on frozen or corroded supply stops.

Saves A Lot Of Time-- if you don't have sufficient exposed copper to cut off the old compression fitting, this angle stop puller will effortlessly remove the old compression ring and reform the previously crimped copper pipe back to a perfect circle. Saves a lot of time around cutting old pipes.. Make Your Life Easy--This sleeve remover removes 12-inch copper water compression sleeve.This compression sleeve puller removes leaking compression sleeves without damaging walls, which effortlessly pulls the nut and ferral off of the pipe.. Operating Steps--1.Remove the old compression fitting or the old angle stop. 2.Put the nut of pipe to the golden threaded mouth of the puller tool to tighten the screw 3.Make sure the ferrule puller is properly aligned with the pipe, and then you are able to remove the nut and ferrule with maybe 10 turns of the handle. 4.The puller tool will automatically pull compression nut and ferrule.. Resistant Wear Resistant.--Even such as the existing supply stops are severely corroded or frozen, you can turn the lever to extract the old compression sleeve from the pipe.Ideal for working on frozen or corroded supply stops,corrosion resistant wear resistant.. 100 QUALITY GUARANTEE ONE YEAR MONEY BACK. Buy with confidence and add to cart now We provide 100 customer support 1-year product warranty. Have any problem, please email us, we'll reply within 12 hours..

ApplicationCompatible with Mack Cummins Volvo Detroit International and other Cat Engines 3176, 3196, 3300 Series, 3400 Series, 3500 Series, C10, C12, C15, C16 Maxxforce DT, DT360, DTA360, DTA466, DT466, DT530 PLN,DT466E, DT530E, DT570, HT570.. Direct ReplacementOur universal cylinder liner puller direct replacement for OEM PT-6400-C, M50010-B and 3376015.. FunctionThis universal liner puller works on wet liners of from 3-78 to 6-14 bore, up to 15 deep, with a minimum wall thickness of .148. Used to safely correctly remove the cylinder liners avoiding damage to the cylinder block.. ImportantThreads must be lubricated with J23444-A or equivalent high pressure lubricant for heavy duty truck applications. Package Includes 1 x Grease AND 1 x Cylinder Liner Puller Tools Kit PT-6400-C.. Superior MaterialCrafted from quality carbon steel, high strength, anti-wear, rust resistance, anti-oxidation, sturdy and durable..

No Damage To Walls Copper Supply LinesThis compression sleeve puller removes leaking compression sleeves without damaging walls, which effortlessly pulls the nut and ferral off of the pipe. This sleeve remover removes 12-inch copper water compression sleeve. If you are in need of replacing a quarter turn valve on a dishwasher, sink or toilet that has compression fittings, buy this sleeve remover tool and make your life easy. Precision machined plumbing tool.. Not Need To Cut Off The PipeSaves a lot of time around cutting old pipes. This puller tool is easy to use in relatively tight spots. Especially if you don't have sufficient exposed copper to cut off the old compression fitting, this angle stop puller will effortlessly remove the old compression ring and reform the previously crimped copper pipe back to a perfect circle. No damage to the copper. Makes removing a nut and ferrule simple, and makes plumbing work simple.. Work On Corroded FrozenFully machined body and screw, this ferrule puller is durable, corrosion resistant wear resistant. Even such as the existing supply stops are severely corroded or frozen, you can turn the lever to extract the old compression sleeve from the pipe.. Easy Fast Remove1.Remove the old compression fitting or the old angle stop. 2.Put the nut of pipe to the golden threaded mouth of the puller tool to tighten the screw 3.Make sure the ferrule puller is properly aligned with the pipe, and then you are able to remove the nut and ferrule with maybe 10 turns of the handle. 4.The puller tool will automatically pull compression nut and ferrule.. Great Compression Sleeve Puller ToolWe love and take pride in our angle stop puller and we back this ferrule blaster up with lifetime service. Have the confidence that this compression ring removal tool will last, if there are any issues of this plumbing tools, just contact us and we will make it right..

This tool removes cylinder sleeves faster than ordinary pullers because it requires little setup time - cone adjustment positions puller jaws quickly then locking bar is tightened - ready to go. To break 'frozen' sleeves loose, adjustable bridge is positioned on the cylinder block then bearing-mounted forcing nut is tightened. Next, bridge is removed and slide hammer assembly is attached - with a few sharp hammer blows from the 5 lb. hammer, sleeve is pulled - an average of less than 2 minutes per cylinder in most cases. Does not require any special adapters to pull sleeves due to adjustable jaw design adjustable jaws allow use on cylinder sleeves ranging from 3 inches to as large as 6-12 inches in diameter. High-grade materials ensure quality performance over the lifetime of the tool comprehensive instructions included.

No Damage To Walls Copper Supply LinesThis ferrule puller removes leaking compression sleeves without damaging walls, which effortlessly pulls the nut and ferral off of the pipe. This compression sleeve puller removes 12-inch copper water compression sleeve. If you are in need of replacing a quarter turn valve on a dishwasher, sink or toilet that has compression fittings, buy this tool and make your life easy. Designed by plumbing professionals. Precision machined plumbing tool.. Not Need To Cut Off The PipeSaves a lot of time around cutting old pipes. Re-designed bullet nose will not pull off and is easy to use in relatively tight spots. Especially if you don't have sufficient exposed copper to cut off the old compression fitting, this angle stop puller will effortlessly remove the old compression ring and reform the previously crimped copper pipe back to a perfect circle. No damage to the copper. Makes removing a ferrule simple, and makes plumbing work simple.. Work On Corroded FrozenEven such as the existing valve was severely corroded or frozen, you can turn the lever to extract the old compression sleeve from the pipe. Make sure the ferrule puller is properly aligned with the pipe, and then you are able to remove the nut and ferrule with maybe 10 turns of the handle. Easy and fast solve the problem of compression valves failing with small leaks. Fully machined body and screw, this ferrule puller is durable, corrosion resistant wear resistant.. 2 Ways To RemoveRemove the old compression fitting or the old angle stop.WAY 1 ONLY REMOVE THE FERRULE---Let the ferrule in between the red notched end of the tool notched clamping ferrule. WAY 2 BOTH REMOVE THE COMPRESSION NUT AND FERRULE---Place red notched end of tool behind compression nut. And then both way1 or way2 all need to Engage the silver head end in tubing. Hold tool firmly while turning the t-bar handle, the puller tool will automatically pull compression nut and ferrule.. Gteat Compression Sleeve Puller ToolWe love and take pride in our angle stop puller and we back this ferrule blaster up with lifetime service. Have the confidence that this compression ring removal tool will last, if there are any issues of this plumbing tools, just contact us and we will make it right..

Compression Sleeve Puller pulls the nut and compression sleeve off of the copper pipes. Use on 12-inch 58 OD copper pipe. Precision machined plumbing tool. Saves time and effort when replacing old angle stops. Great handyman tool.

Plumber's Puller Kit.

No DamageVKALTUL pipe olive remover puller tool is used to remove used or damaged olives from the air-conditioning pipes without damaging the pipe by uillizing compression fittings to lock nut. It can increase torque and remove olives more easily.. Two in OneThe olive puller is combined with one double hex and one single hex wheel socket. The double hexagonal one is suitable for 1 2 inch diameter brass pipe, and the single hexagonal one is suitable for 3 4 inch diameter copper pipe. Two in one design is easy to carry and store, and does not occupy space.. Premium MaterialThis compression ring removal tool is made of solid brass with high strength, high hardness, corrosion resistance, wear resistance, high finish, which have long service life.. Easy to UseFerrule blaster ferrule puller is easy to operate, and you can work without reading the manual or using other tools, reducing the working time and improving the working efficiency.. Save EffortThe zinc-plated Tommy bar at the head of ferrule puller is designed by the lever principle, and can move left and right according to the demand to achieve the effect of labor saving..

Bleckman Compression Sleeve Puller.