Top 8 Best Stepper Controller

Power supply 15-160VDC or 5-12VDC. If you are using 5-12VDC power, positive end connect DC 5-12V Input, negative end connect Common Cathode End.. 3 Frequency High 5.8KHZ-127KHZ, Mid 590HZ-15.8KHZ, Low 82HZ-2.3KHZ. To control the stepper motor, mus connect to the driver. PUL and PUL- pulsed positive and negative EN and EN- is to enable the positive and negative terminals DIR and DIR- are the positive and negative directions.. Frequency of measurement can amount PUL and common cathode terminal GND two ports..

Number of controlled axis Single axis can achieve a variety of complex operation positioning control and non-positioning control. Display digits 8 digital display, manual automatic status display, run stop status display, the number of steps counts procedures display, edit the program, parameter display, input output status display, pulse and direction display . Autorun feature You can edit, you can control the start and stop automatically run through the panel buttons and processing and other operations at the terminal level. Manual operation functions position adjustments manual jog speed and jog the number of steps can be set. Operating state Autorun mode, manual operation, the program edit mode, parameter setting statusThe maximum output frequency 40KHZOutput frequency resolution 1HzPower supplyDC24V.

Model NumberDDCS V3.1 5 inches TFT screen, resolution ratio 480x272,17 operation keys. Feature16 photoelectric isolated digital inputs,3 photoelectric isolated digital outputsthe highest output pulse per axis is 500KHz. This provides high control precision for stepper motors and servo motors.. SB flash disk4G USB flash disk support for G code file input,no size limited of the G-code file ARM9 main control chip,FPGA core algorithm chip. Power requirementsThe Power Supply for the controller is 24VDC,DDCSV3.1 needs two power supplies,main power is for system,IO port is for input and output ports, Current is not less than 1ABecause of the IO power,system can supply the power for all IO ports.So no need the external power supply for IO port anymore. MPG with 15-pin connectorMPG Resolution100PPRSwitchX1,X10,X100DDSCV3.1 Version enhenced Algorithm,support soft interpolation,fixed arc interpolation bug of the old versionSupport standard MPG Jog function for each axis continuous, step, defined distanceCustomer can define the distance.

Package included 1 x Stepper Motor Driver.. Stepper Motor Driver 9V-42V DC power supply, H bridge bipolar constant phase flow drive. The maximum 4.0A of the eight kinds of output current.. The largest 32 subdivision of the 6 models are optional Suitable for 4Wires, 6 wires and 8 wires stepper motor. it can control 2 phase stepper motor forward and reverse rotation, With 1-2, W1 -2 , 2W1 -2, 4W1 -2 phase excitation mode.. Protect form Energy-saving semi-automatic current lock function, built-in temperature protection and over current protection, under voltage protection, Preventing reverse.. Suitable for a wide range of stepping motors of Nema 17, 23 and 24 can used in various kinds of machines, such as X-Y-Z tables, labeling machines, laser cutters, engraving machines, pick-place devices and so on..

Suitable for Nema 23 ,Nema 24 and Nema34 Stepper Motor2-phase hybrid stepper motors Outer diameter 57, 60,86mm.. This high subdivision driver is suitable for high subdivision motor. Suitable for stepper motor 57,60,86 type 2-phase 4-wire, 6-wire, 8-wire. Anti-Resonance for optimal torque, extra smooth motion, low motor heating and noise. Package 1piece DM556 driver. PLEASE NOTE if there is any problem, please feel free to contact us, each defect items could be refunded or reshipped, we will try out utmost to support you..

This module is a pulse generation module, supply the control signal to stepper driver. To control the stepper motor, it must be equipped with a drive.. This simple controller stepper motor stepper motor DC power supply can be composed of a simple set of control platform.. The controller has high 5.4k-160khz, middle 540-16.6khz, low 80-2.4khz total of 3 kinds of low frequency signal can be used to select the jumper.. Can produce pulse signal, can also produce PWM signal, can choose the jumper.. The frequency of measurement PUL and common cathode end..

4 axis CNC Controller kit for Mill, Lathe, Router, and other specialty CNC machine tools. On-board motion control CPU Beagle Bone Green ARM cortex A8 with Ethernet communication to the CNCPC. 8 inputs 8 outputs, Easy CNC Setup Wizard, Legacy DB25 connector, command stepper motors and AC brushless motors. Runs on Centroid industrial Mill and Lathe CNC software Windows 10, Touch Screen Compatible Operators Control panel. Three Software Levels, Free 50Kb file size limit, Pro and Digitizing Bundle see website for full details. User editable Virtual Control Panel.. Spindle Encoder input, VFD Spindle control analog output, Industrial CNC features at DIY price.

Product4 Axis nema23 stepper motor driver usbcnc controller kit Model Number23HS2430BFMD2740C. Stepper MotorNema23 57 typeStep Angle 1.8 Current 3.0A Holding torque 425oz-in 280Ncm Shaft Dual Shaft,8mm diameter Wirings ARed A-Green BYellow B-Blue. DriverFMD2740C driver Voltage DC12-50V Driver microstep128microstepCurrent rated maximum output reaches 4A Subdivision precision 2 8 16 32 64 128 10 20 optional. 4 Axis USBCNC Breakout BoardUSB port,only support USB CNC Software,not fit for Mach3 software.Our parcel include a CD,it include the user manual and USBCNC software. 400W 36V 11A DC Switching power supplyPlease flip the side input voltage selector switch,Input AC110V-120V or AC220V-240VComputer system Support Win XP7810,if you can not get the activation code on Win 10,pls let us know,we will help you to solve it..

Model NumberDDCS V3.1 5 inches TFT screen, resolution ratio 480x272,17 operation keys. 16 photoelectric isolated digital inputs,3 photoelectric isolated digital outputs. USB flash disk support for G code file input,no size limited of the G-code file ARM9 main control chip,FPGA core algorithm chip. The Power Supply for the controller is 24VDC,DDCSV3.1 needs two power supplies,main power is for system,IO port is for input and output ports, Current is not less than 1ABecause of the IO power,system can supply the power for all IO ports.So no need the external power supply for IO port anymore. 3.1 Version enhenced Algorithm,support soft interpolation,fixed arc interpolation bug of the old versionSupport standard MPG Jog function for each axis continuous, step, defined distanceCustomer can define the distance.

Comes with CNC USB port interface breakout board. 4.5A ST-4045 stepper motor driver, ensure the stable operation of equipment. 350W 36V switching power supply the range of AC input voltage is changed by the switch. 57HS76 stepper motor, powerful and stable to work.. Easy to assemle, simply to DIY..